As indicated, you receive 2 yellow smiley-faced balls on a string and 2 tiny eyelets that you would screw into a rafter. If you need to attach to drywall, I would advise using an anchor rather than something else. The eyelets, in my opinion, might be a little bigger. When I was screwing it into wood, one shattered (eyelet twisted off the screw end).Parking your car where you want to is quite straightforward. Next, locate a position straight up on the garage ceiling where you want to hang this from. I believe it is preferable for this to strike the windshield exactly in front of the driver's field of vision rather than the center, which would be offset from your field of vision when parking. Additionally, you can see when you are very close by a shadow beginning to form on the ball's bottom, letting you know that it will only be a few inches before it strikes your windshield. You might want to allow yourself some leeway if at all possible.Using the adjustable clip, you may make more precise adjustments such as moving the clip lower to touch the windshield earlier or higher to hit later.When the garage door is closed, it simply hangs there and does not retract. To accomplish this, you would need to add more string and one or two pulleys to accommodate the required length of string.I threaded the rope through the eyelet and tied it to the clip on the push side to make this relatively "retractable" so it is out of the way when our car is not in the garage. Instead of attempting to catch some slack in the string, the ball slides up and down the string in this manner. With some white electrical tape that will also stop it there, I highlighted the location where I want this to be when the ball is fully dropped. I may adjust this later, but so far, so good:-)

Each strip is flexible and cuttable, allowing for the creation of multiple pieces or various shapes. The wall protectors can be applied to 90-degree walls, curved surfaces, or cylinder columns thanks to their ideal flexibility and softness, which are provided by their ideal thickness.

Fiberglass Mesh Adhesive Structure – Its distinctive integrated back adhesive structure strengthens the adhesive force. The wall protectors can be removed thanks to the interlaced fiberglass without damaging the soft protector or leaving marks on the wall. The self-adhesive cover can be easily peeled off without tearing.

You will receive two Garage Smith GWP02S car door protectors, worry-free 6-month warranty, and customer service and technical support with a 1-day response time.

Superior Quality and Eco-Friendly Materials The protectors have a diamond-textured waterproof surface that prevents scratches, and they are made of odorless, high-density material that has received RoHS authentication. The material is entirely eco-friendly. We should go green!

Great Impact Absorp

I found *exactly* what I was seeking for in these protectors. They are the ideal thickness and will shield your garage door from unintentional dents. Simply peel the protective covering off the adhesive backing and stick for a very easy installation. I'm done now. Make sure you test fit the door to determine the precise location of the wall contact—it could not be there!These have been installed for a few weeks, and so far there have been no symptoms of them coming loose. Happy with this purchase a lot!

I found *exactly* what I was seeking for in these protectors. They are the ideal thickness and will shield your garage door from unintentional dents. Simply peel the protective covering off the adhesive backing and stick for a very easy installation. I'm done now. Make sure you test fit the door to determine the precise location of the wall contact—it could not be there!These have been installed for a few weeks, and so far there have been no symptoms of them coming loose. Happy with this purchase a lot!

I had been sporadically seeking for anything like this for a few years. On my side of the garage, there is framed peg board, and every now and then, when I would come a little too close to the wall, my doors would open into the frame of the peg board. Sadly, before I purchased this wall protector, my old car's paint was chipped.Installation would be relatively simple if the surface were flat. It was a little challenging to shape the material in an elbow shape while rolling it out and pressing to the wall because I was trying to cover a wooden frame that protrudes slightly more than a quarter inch from the wall as well as the wall directly beneath the frame. In retrospect, applying a strip that was wide enough to cover the bottom frame face to the frame face would have made more sense. Apply the remaining paint to the dry wall after that.I did cut one of the rolls in half to aid in the installation. This makes a one-person installation a little bit simpler. With regular scissors, the material was simple to cut. It has been standing for about two months and appears to be in good condition.

Exquisite Surface Design: It's the little things that count. The world's most stunning design has been used to create this garage car door guard. Every water drop or water flushing will be stopped by specific grooves and textures. Additionally, cleaning it is really simple.

Double Protection by Dual Strip Pack - Two garage wall strips in a set guarantee that the walls and doors of the garage will be completely covered on both sides.

Top Quality and Eco-Friendly Material The protectors are composed of odorless, high-density material with RoHS verification, and have a diamond texture on the waterproof surface for scratch prevention. The material is entirely eco-friendly. We should go green!

Full Protec

I had been sporadically seeking for anything like this for a few years. On my side of the garage, there is framed peg board, and every now and then, when I would come a little too close to the wall, my doors would open into the frame of the peg board. Sadly, before I purchased this wall protector, my old car's paint was chipped.Installation would be relatively simple if the surface were flat. It was a little challenging to shape the material in an elbow shape while rolling it out and pressing to the wall because I was trying to cover a wooden frame that protrudes slightly more than a quarter inch from the wall as well as the wall directly beneath the frame. In retrospect, applying a strip that was wide enough to cover the bottom frame face to the frame face would have made more sense. Apply the remaining paint to the dry wall after that.I did cut one of the rolls in half to aid in the installation. This makes a one-person installation a little bit simpler. With regular scissors, the material was simple to cut. It has been standing for about two months and appears to be in good condition.

I found *exactly* what I was seeking for in these protectors. They are the ideal thickness and will shield your garage door from unintentional dents. Simply peel the protective covering off the adhesive backing and stick for a very easy installation. I'm done now. Make sure you test fit the door to determine the precise location of the wall contact—it could not be there!These have been installed for a few weeks, and so far there have been no symptoms of them coming loose. Happy with this purchase a lot!

If I hadn't placed the garage protector there, my husband's door would have harmed the side of the wall where it opens. The wall where the door would hit or the little places where a car could crash can easily be attached using this thick foam. Even though it saved us money by preserving the car's door, spending $20 or more on two tiny pieces of foam didn't seem like good value. I wish there was a less expensive choice.

ordered this item to, you guessed it, fill our garage. We were reluctant to park our automobiles in our garage because of the growing gap between the size of cars and the size of garages, which was unfortunate. After reading the reviews and following the advice of a family member, we chose this. They're excellent! You could open your automobile door quite forcefully without worrying about harming it because it was thick and padded. Although we certainly could have found larger ones if we had looked, they are a touch on the little side, so for the posts in our garage, we used 2-3 to cover the regions we needed to cover. Overall, we are quite happy with our purchase!

To safeguard our doors, I ordered these to install in the metal rafters of our carport. They are flawless. I simply put them on without bothering to cut them to size. They are durable, waterproof (which is crucial when living in the Pacific Northwest), and useful. None to report!

These things I bought functioned flawlessly. Every time my spouse or I tried to park in our two-car garage, we ended up hitting the chest freezer or shoe rack. The clear coat shield and our front bumper suffered severe damage as a result. The paint repair company warned us that if we kept breaking the clear coating seal, the bumper would need to be taken apart and fixed. The cost of repairs was estimated in the thousands. We haven't done any more harm since installing the LED light parking stop signs. One of my best purchases from last year was this. Thanks!