4' 4-pole copper wires that are color-coded and a 25' split Y-style harness

Kit contains a wire harness, two amber clearance lights, and stop, tail, and turn signal lights.

consists of a 23-foot copper wiring harness with UV-resistant coats.

Under-80" trailer light package that complies with DOT requirements

Large 4.5" x 5" lenses, along with a bracket and license plate light#

Everything required for a simple fix is included in this package. good value for the money. I doubt I would use it for a boat trailer now that I believe I have a firm grasp of trailer lighting.1. Use high-quality shrink tubing and solder all of the wire connections.2. Remove all mounting nuts and clean all ground connections to the bare metal.3. Ensure that all wires are running to eliminate the possibility of them snagging on anything. Use cable ties to bundle any extra length.4. Spray paint the connectors and surrounding area with a few coats of high quality (Rustoleum?) paint once all ground connections and mounting bolts are finished and tested.

For my project, ideal. All of the indicators have been tested, and they are functional. Their two-wire lead measures roughly 7 1/2 inches in length. Without the supplied self-adhesive gasket, the marker measures just under 4 inches in length, 3/4 inches in width, and just under 7/8 inches in thickness. A package of nuts, washers, and bolts were provided by the vendor. My 1990 30 foot Coachman Travel Master RV employs corrugated fiberglass paneling for structural side wall strength, thus I needed a marker with a low profile to fit flushly on the side. The valley area of the siding can accommodate these LED lights flush. These appear to be ideal for the project. Now I'll connect them to the parking lights as side markers and float the ground with the turn circuit so the marker can indicate my intention to change lanes or make a turn. Additionally, auto relays must be utilized since the diode lights are diode lights if the ground is to be floating between the turn and marker positive voltage circuit. Connect the left and right sides to different relays. The marker lights will flash out of phase with the front and rear signal lights of the vehicle when the turn signal is activated and the marker lights are on. These LED side markers will flash together with the other turn signals if the parking light circuit is not functioning. The markers are not that apparent in direct sunlight. At night, they are excellent. not too bright as to be annoying. ASSIGNMENT: 10/14/2019 The lights are still all functioning properly. The amber lens has slightly faded, but not enough to be an issue.

Application: Universal for Tractors, Semi-Trailers, Dump Trucks, Buses, Boats, Special Vehicles, etc.

12 red, 3 red, and 4 white diodes total 19 LED Combination stop-turn tail-side marker light with reflector and license illuminator for the street; Driver Side Performs 7 Tasks: stop sign, turn signal, tail light, rear reflex reflector, side marker light, side reflex reflector, and illuminater for the license plate;

Includes: 1 pair of lights, 2 gaskets, and 4 screws in the package. The ONLY official vendor of Partsam products is PARTSam. Please contact the seller for a refund if you receive a product that is not branded with PARTSam or does not come in PARTSam packaging with the logo.

Lights on a boat, snowmobile, camper, or utility trailer should be added or upgraded; High visibility safety lights are EASY TO INSTALL, and wiring instructions are provided in the product description. Completely waterproof and sealed, the acrylic len are designed to keep water out and preserve the circuits. Maximum visibility and safety are provided by extremely brilliant LED lights. These powerful trailer lights are long-lasting and fully functional in adverse conditions.

12 red and 3 red diodes total 15 LED Curb Side Combination Stop Turn Tail Marker Light with Reflector; Six roles are served by the passenger side: stop, turn signal, tail, rear reflex reflector, side marker, and side reflex reflector.#

When one of my non-LED tail lights blew a bulb and needed a bulb insert assembly to replace it, I decided why not just buy a new set of LEDs. Submersible wasn't a necessity for me because I tow a motorbike trailer, but they'll still be better sealed all around for rain or dust.There are no instructions at all. You can look at the seller's description, and good luck if you can understand it. It took some trial and error to figure it out because the wire colors have nothing in common with what I am familiar with.I had to drill 2 new holes because the light was too close to the trailer due to the positioning of the studs. No huge difficulty, although it was necessary to drill a stud hole for the ground wire. No huge deal, there was also ground wiring to be done. If you have a good drill, drill bits, ring terminals, a wire cutter, a ring terminal crusher, and a bolt for the ground wire, it shouldn't be a problem. Additionally, the cables that stick out the back of the light are not recessed; you must lay them flat behind the light and hold them there while pressing the light against the trailer mount. Then, you must tighten everything down, but not too much. To keep everything in place, I used blue loctite, but you'll also need loctite.They are good lights overall, bright and efficient, but mounting them was a bit of extra work. This is typical for anything that should fit virtually everything; occasionally it will be nearly perfect and other times it won't.

The positives include a fair pricing, brightness, standard stud/mount arrangement, and the fact that all lights are LEDs (unlike many others with incandescent side markers).The bad: The running light and stop/turn wires for the left side light were switched. Simple connection swapping at the light wires will fix the issue. Simply turn on the lights before crimping any connectors!

Price: More affordable than any nearby retailerLight: Exceptionally brightInstallation: I replaced the two included screws with two self-tappers instead of using the two supplied screws. Simply peel the plastic covering off the ground and live wire ends to access the wires. very simple to installFor my boat trailer, I decided to buy two of these. The metal strip's black contrast looks fantastic against the color red.The lights have not yet been submerged, but I will do so and provide a follow-up review to see how it goes.

This small package is excellent. I was first concerned since my trailer, which is around 2 feet long, had a lot of wire. But it fit perfectly and was simple to install. Both waterproof and lead, they. They are finer than my previous set and shine brightly. They look terrific.

Kit contains a wire harness, two amber clearance lights, and stop, tail, and turn signal lights.

meets DOT requirements; side lenses have a standard bulb. housing that resists corrosion. for trailers no wider than 80 inches

High-visibility LED taillights have a longer lifespan than conventional incandescent ones.

contains a 23-foot wiring harness with UV-resistant jackets.

comes with a 4-pole, 23 and 4 foot color-coded wiring harness. Lighting and electrical products#

This small package is excellent. I was first concerned since my trailer, which is around 2 feet long, had a lot of wire. But it fit perfectly and was simple to install. Both waterproof and lead, they. They are finer than my previous set and shine brightly. They look terrific.

There is NO incandescent bulb used in the side lens light or the side marker lights; they are ALL LED! Superb LED quality that complies with DOT requirements

CUSTOMER SUPPORT AND SOME NEW ARRIVAL: If there is a problem with your order or use of our items, please get in touch with us right away. We are always available to help you. There are some new arrivals with really attractive prices listed in the product description that you might find interesting.

The CZC AUTO 12V Submersible LED Trailer Light Kit comes with a license plate bracket, two amber LED marker lights, a 25-foot wiring harness, two combination stop, tail, and turn signal lights, and a mounting hardware pack.UPDATE AS OF JUNE 9TH, 2019.WE AMPROVED THE WIREHARNESS TO 18GAUGE 100% COPPER WIRE FOR WATERPROOF USE TO BETTER SERVE OUR CUSTOMER.

Testing for Waterproof and Submersible Features (2nd Image):We submerged the light for 3 hours, three times daily for a total of 5 days, and it was really effective! The lights are underwater and undoubtedly waterproof. Prior to marine/underwater use, please ensure that the wires are connected properly and there are no electronic shorts.

Application for towing vehicles with a width of less than 80 inches, such as boats, trucks, snowmobiles, etc. Please take note that the PCB of these trailer lights, not their housings, is sealed. You might discover that the housings have huge holes in them. The housings are not completely sealed, therefore when submerged in water, water will flow in and out of them through the gaping gaps.#

The trailer light kit is just as described. It was rather simple to install and of decent value.Better instructions might have been provided. Putting this package doesn't take long, but the directions for installing the side markers were absolutely wrong. They instruct you to connect the side marker's two wires to the brown wire on the lighting harness. Actually, all that is required is to fasten the white ground wire from the marker to the trailer and connect the brown wire from the marker to the brown wire on the harness. I struggled with this for over 45 minutes until I finally got it.I would admit that of all the Amazon vendors I have dealt with, this merchant provided the finest customer service. One of the side markers was removed from its container. A wire was incorrectly soldered to the board. Even though I only asked for one item, they sent me a complete replacement because they were prompt to reply to my request, considerate and polite in their handling of my problems. I'd purchase from again.

DOT approved

consists of two 4-1/2 "diameter amber flasher on the opposite side of the red brake light.

The lights are kept in place by a powerful magnetic base with an 11-lb pull.

includes a standard 4-flat wire vehicle trailer hookup and a 20-foot color-coded wiring harness.

Perfect for all towing uses under 80 "wide#

I really adore these. I took a gamble because I didn't have enough time to rewire my old fold-up trailer this summer. I attached some galvanized plates by drilling through floor boards. They held up pretty well considering how much my trailer bounces. In order to position them where they will be optically taller, I intend to create little boxes with the plates at the bottom that I can attach to side walls or the rear.

I really adore these. I took a gamble because I didn't have enough time to rewire my old fold-up trailer this summer. I attached some galvanized plates by drilling through floor boards. They held up pretty well considering how much my trailer bounces. In order to position them where they will be optically taller, I intend to create little boxes with the plates at the bottom that I can attach to side walls or the rear.